|
COMMERCE BUSINESS DAILY ISSUE OF FEBRUARY 23,1998 PSA#2037National Park Service, Mount Rushmore National Memorial, PO Box 268,
Keystone, SD 57751-0268 46 -- FLOATING ASPIRATION EQUIPMENT-WASTE WATER TREATMENT PLANT SOL
RFQ1500-8-0002 DUE 030298 POC Ron Eilefson, PH:605-574-2523
Fx:605-574-2307 This is a combined Synopsis/Solicitation for commerical
items prepared per the format in Subpart 12, as supplemented with
additional information included in this notice. This announcment
constitutes the only solicitation; proposals are being requested and a
written solicitation will not be issued. Further information upon
written request. solicitation number for this is RFQ1500-8-0002; is a
Request for Quote. The following Provisions and Clauses are
incorporated into this RFQ by Reference and are in effect through
Federal Acquisition Circular 97-02, December 15, 1997. No addenda pply
to these provisions & clauses. FAR 52.212-1,Instructions to Offerors.
Commercial Items FAR52.212-3, Offeror Representation and
Certifications Commercial Items FAR52.212-4 Contract Terms and
Conditions Required to Implement Statutes or Executive
Orders-Commercialitems no additional FAR clauses apply. SIC:4952, $5.0
million NPS REQUIREMENT: The National Park Service at Mount Rushmore
intends to purchase two floating, self-contained, electric
motor-driven,propeller-type, horizontal, integrated, fine-bubble
aspirating aerators. Each aerator shall be capable of providing at
least 1.50 pounds per horsepower per hour of oxygen transfer under
clean water conditions. Claimed oxygen transfer rates shall ahve been
verifed by independent agency testing. Each unit shall be as described
below: The drive motor and upper portion of the aerator shall be above
the water surface and supported by a float assembly incorporating four
pontoon floats. Floats shall be molded low-density polyethylene filled
with urethane foam. Minimum individual float buoyancy shall be 600
pounds. Floats shall be connected by a galvanized steel framework which
permits rotating the 45 degree inclined aerator completely up and out
of the water for field servicing the unit from a grated work surface.
The framework shall include a 316 ss mounting flange which permits
removal of the aerator while leaving the motor in place. Each
aspirating aerator assembly shall include a splash related submerisble
drive motor,drive shaft and coupling, hollow shaft housing, lower
bearing, sleeve, propeller, air diffuser, and vortex shield. The
submersible cast iron frame motor shall be 25 hp, 1.15 service factor,
1800 rpm,230/460 volt, 60 Hz,three phase type specifically designed
for inclined service. Permissible shaft runout shall not exceed 0.0025
TIR. The hollow drive shaft shall be 316 ss full-welded to a carbon
steel universal joint coupling. A replaceable zirconia sleeve shall be
securely attached to the shaft at the bearing location. The housing
shall be 316ss. The lower end of the housing shall have a field
replaceable, molded elastomer, fiber backed process liquid lubricated
bearing. openings shall be provided for air intake and bering liquid
lubrication. The field replaceable, self-tighting, investment-cast 316
ss propeller shall be specifically designed to maximize oxygen
transfer and mixing characteristics. The entire flow of aspirated air
shall pass through the propeller via the hollow drive shaft. A 316ss
diffuser on the end of the propeller shaft shall expel the aspirated
air fas fine as bubbles per EPA report #EPA-600/2-82-003. An
anti-vortexing, anti,cavitation sheld shall be provided. All mounting
hardware and cables shall be stainless steel. The aerator unit shall be
cable stayed to the existing structure to maintain its position in the
treatment basin. Due to space constraints, the aerators shall be
suitable for field assembly inside the covered treatment basin. The
aerator unit shall include 12 month unconditional labor guarantee and
concurrent 36 month unconditional parts guarantee. (0050) Loren Data Corp. http://www.ld.com (SYN# 0236 19980223\46-0002.SOL)
46 - Water Purification and Sewage Treatment Equipment Index Page
|
|