Loren Data's SAM Daily™

FBO DAILY ISSUE OF DECEMBER 10, 2010 FBO #3303
SOLICITATION NOTICE

20 -- Shipboard Insulation Repairs

Notice Date

12/8/2010
 

Notice Type

Combined Synopsis/Solicitation
 

NAICS

238310 — Drywall and Insulation Contractors
 

Contracting Office

Department of the Navy, Military Sealift Command, MSC East - Norfork, Virginia, Bldg 238/2 B Street, Camp Pendleton, Virginia Beach, Virginia, 23451
 

ZIP Code

23451
 

Solicitation Number

N40442-11-T-7169
 

Archive Date

12/29/2010
 

Point of Contact

Roy J. Williams, Phone: 757-443-5960
 

E-Mail Address

roy.williams@navy.mil
(roy.williams@navy.mil)
 

Small Business Set-Aside

Total Small Business
 

Description

This is a combined synopsis/solicitation for commercial items prepared in accordance with the format prescribed in Subpart 12.6 of the Federal Acquisition Regulation (FAR), as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; proposals are being requested and a written solicitation will not be issued. The solicitation number is N40442-11-T-7169, and it is being issued as a request for quotation (RFQ). The solicitation document and incorporated provisions and clauses are those in effect through Federal Acquisition Circular 2005-46, effective 29 OCT 2010. NAICS code 238310 applies. This is a small business set-aside. Military Sealift Fleet Support Command (MSFSC), Norfolk, VA intends to award a firm fixed price purchase order for USNS MERCY for the following services: The requested period of performance for the below service is 01DEC2010-30JAN2011. Provide services of a qualified marine repair firm specialized in shipboard mechanical and electrical installation and repairs for accomplishing various insulation repairs throughout the ship. A. GENERAL REQUIREMENTS: 118151/010300/25230 1. Contractor shall provide all labor, material, hardware, staging if required and tools to accomplish this work. Ship's tools shall not be used during this work. 2. Clean, prepare, prime and paint all disturbed surfaces to match. If required paint will be provided as GFM. 3. The list of the locations and systems is provided as "INSULATION REPAIRS MASTER LIST" 4. Contractors are encouraged to conduct a shipcheck prior to submit their bids. 5. All material shall be ASPESTOS FREE and USCG/ABS approved. Contractor shall submit MSCREP all MSDS sheets prior to work commencement. B. STATEMENT OF WORK: 1. Remove, provide and install, repair and replace as needed all insulation work described in attached Master List. 2. Paint all newly installed and repaired lagging as original. Blankets shall not be painted. VESSEL LOCATION: 32nd Street Naval Station, Pier 1 San Diego, CA POC: Port Engineer: Deniz Ovecoglu, Phone: 757-803-4488 Email: deniz.ovecoglu@navy.mil INSULATION REPAIRS MASTER LIST ZONE 1 1. In MTF Laundry steam piping supply and return for the "Flat work ironer" ½" and 1 ¼" piping. Steam service. 2. In Laundry space fwd most press needs lagging on a steam supply line. ½" pipe. Steam service. 3. Level 5 a fire main pipe is missing lagging near the valve. Pipe size 2 ½" with tee to 1". ZONE 2 1. Steam supply line to hot water heater located in service area 2 has damaged lagging. Pipe size 1 ½". Steam service. 2. Steam supply line to hot water heater has an exposed section of pipe. 2" steam piping. 3. Fire Main to eductor has a section where the lagging was removed. 2" salt water pipe into a 2" tee reducer to 1 ¼" SW piping. Neoprene type insulation. 4. Missing lagging on s.w. pump discharge piping located on aft bulkhead. 2" saltwater piping. Neoprene type insulation. ZONE 3 1. Lagging missing from system crossover piping in service area 3. Pipe size 2 ½" with neoprene insulation. Located above potable water tanks 1 and 2. ZONE 4 1. Condensate return line has fallen off pipe. Location in overhead section of service area 4. pipe size ½" steam pipe. 2. In upper section of service area 4. vertical pipe runs have bare steam piping. A 3" laundry steam supply, a 2 ½" heating steam supply and a ¾" condensate return pipe. All insulation is for steam service. 3. Hot water heater located in service area 4 is missing lagging from regulator valve to water heater. 2 ½" steam piping. ZONE 5 1. Hot water heater, hot water outlet of heater has a section of pipe that is missing insulation. Pipe size: 2" copper insulation for hot potable water service. 2. Hot water heater has an uninsulated section of pipe after the steam regulator to the heater. Pipe size: 2" insulation for steam service. 3. Potable water fill piping located in overhead of service area 5. Insulation was removed to patch pipe leaks. Pipe size 2 ½" with neoprene type insulation. ENGINE AND AUXILIARY MACHINERY ROOMS 1. LP Bleed Line. Insulation rip by reduction gear. Pipe size approx 6". Insulation for steam service. Hard wrapped 2. Steam Inlet to fire pump Lagging ripping around valve. 3" globe valve. Insulation for high temp steam service. 3. LP bleed extraction valve. Lagging coming undone. 3" valve. Insulation for high temp steam service 4. 1st Stage feed heater. Insulation rips across top of heater. Insulation rip in gland exhaust inlet line. 1" thick. Neoprene type insulation glued to heater. 5. LP. bleed reg station: lagging ripped in between lp bleed to aux exhaust and inlet valve. Insulation for high temp steam service. 6. Astern guardian valve: lagging ripped around valve. 6 or 8" valve. Steam service. insulation high temp. 7. Aux Exhaust dump to condenser line: small insulation rips along line. 6 or 8" steam service piping- high temp. 8. Steam to forward station line: Lagging ripped on gate valve. Steam service valve 6". Insulation for high temp steam service 9. Aux Steam Line: Insulation rips by main steam stop valves. 6" aux steam service piping. High temp steam service insulation. 10. drain lines: lagging rips in drain lines by main steam stop valves. ½" pipe. Insulated for high temp steam service. 11. Gland seal regulator: insulation rips in steam supply line to regulator. Approx ½" pipe. Insulation for high temp steam service. 12. 870# - 140# Aux steam reduction station: lagging ripped around inlet and outlet valves. Insulation ripped before inlet valve, insulation ripped after outlet valve, lagging ripped in drain line. 6" pipe and 1" pipe. Insulation for high temp steam service. ENGINE AND AUXILIARY MACHINERY ROOMS (cont.) 13. Aux exhaust dump to reg line: lagging ripped around inlet valve. 4" valve. 14. Air Ejectors: lagging ripped in steam supply lines to second stage, lagging ripped around valve in steam supply to 1st stage. ¾" or 1" pipe size. Insulation for high temp steam service. 15. #1 Main Feed Pump: lagging ripped around discharge valve. Insulation and lagging around pump casing. Steam inlet valve lagging ripped. Steam and hot water piping. 4" and 6" pipes, Insulation for high temp steam service. 16. #2 Main Feed Pump: lagging ripped around discharge valve. Insulation and lagging around pump casing. Steam inlet valve lagging ripped. Turbine exhaust valve lagging ripped, safety valve lagging ripped. Steam and hot water piping. 4" and 6" pipes, Insulation for high temp steam service. 17. Inport feed pump inlet line: insulation ripped in feed water branch from main feed to pumps. 2" piping. Insulation for high temp steam or 275 degree hot water service. 18. DFT: Insulation rip on vent line to gland exhauster. 1 ½" pipe, return line from feed pumps 2" pipe: insulation rips. DFT main body: torn isulation at bottom of tank. All insulation is prefomed for steam pipes. Insulation for high temp steam service. 19. Starboard Steam Drum: torn insulation on steam drum. Insulation for high temp steam service. 20. Port Steam Drum: Steam drum insulation torn. High pressure, high temperature steam service. ½" valve in sensor line needs new insulation. Sightglass isolation valves need to be insulated. Torn insulation on ½" drain line. Insulation for high temp steam service. 21. Aux Steam line: lagging around valve in sensor line above port steam drum ½" valve. Torn insulation and lagging in aux steam line to soot blowers 1 ½" steam pipe. Torn insulation on Port and Stbd Boiler aux steam line. 6" high pressure, high temp steam service. Insulation for high temp steam service. 22. Air heaters: steam lines to air heaters have various insulation tears. Insulation for high temp steam service.. 2" steam piping. 23. Superheater Steam lines: Port and Stbd superheater vents need to be relagged, 1" high pressure high temperature steam piping. Stbd superheater drain valves fire cloth wrapper has deteriorated. Stbd boiler needs relagging around s.h. safety valve flange. Stbd Boiler superheater to control desuperheater insulation deterioration. High pressure, high temperature 6" steam piping. ENGINE AND AUXILIARY MACHINERY ROOMS (cont.) 24. Feed Water Lines: Insulation torn along feed water lines into economizers. 25. Back of Boilers: common vent line for both s.h. vents need relagging. 1" high temp, high pressure steam piping. 26. Mud drums: relag forward end of both mud drims. Drain lines of both mud drums have have torn wrappers 1 ¼" or 1 ½" high temp, high pressure steam lines. 27. Steam line to burners: Lagging is deteriorated. ½" high temp steam piping. 28. 35 PSI steam line: insulation wrapper torn along line 3" steam piping, need to be lagged on 1 1/2 " line leading to hot water heater. High temp steam piping, 29. 870-135 reducing station: 3" steam pipe-high temp-. Piping needs relagging, valves and regulators need reinsulating. 30. Potable water line: discharge from pumps needs to be lagged or needs relagging. 1 ¼" to 1 ½" pipe. Neoprene insulation for low temp potable water service. 31. Auxiliary exhaust line to L.O. tank. Parts unlagged. Some relagging needed. 1" steam pipe on supply. ¾" steam pipe on return. Insulation for high temp steam service. 32. Aux steam inlet to fire pump: drain line ½" steam pipe. Approx 4 feet of lagging missing. Insulation for high temp steam service. 33. Aux exhaust line from fire pump: 6" steam pipe. Insulation for high temp steam service. 34. Contaminated drain tank and atmospheric drain tank: Tanks need to be re- insulated. Insulation for high temp steam service. 35. 870-140 steam reducing station to evaps: 1 elbow, 2 valves, 5 feet of piping 4" steam pipe. Insulation for high temp steam service. 36. 870 steam to air ejector valve reducing station: ¾" steam pipe.. miscellaneous work needs to be done. Re secure valve lagging and reinsulated reduing valve. Insulation for high temp steam service. 37. Aux steam line to evap reducer: poorly lagged 4" steam line run in overhead above ows. Insulation for high temp steam service. 38. Aux salt water cooling pumps: damaged insulation in discharge line. 8" cu ni water pipe for sea water service. Neoprene type insulation for low temp sea water service. ENGINE AND AUXILIARY MACHINERY ROOMS (cont.) 39. 1" fire main line in lower e/r: torn insulation: 1" pipe for sea water service. Neoprene type insulation for low temp sea water service. 40. Lube oil heater( steam) for L.O. purifier: ¾" steam pipe lagging missing in the steam heater circuit.. Insulation for high temp steam service. 41. Steam supply to purifier l.o. heater. 1" pipe. Insulation for high temp steam service. 42. HP Drain line: 1" pipe Insulation for high temp steam service. 43. Steam Line to forward stations: insulation damaged above #1 main circ line. 4" steam pipe, Insulation for high temp steam service.. 44. 140# steam line in pump room. 4" steam pipe lagging damage in pipe run above door to a/c flat. Insulation for high temp steam service. 45. Chill water pipe lagging above sink in mach shop damaged: 8 or 10" pipe neoprene type insulation. 46. Drain line for steam to air ejectors on #3 and #4 evaps: lagging missing exposing hot pipes. ¾" steam pipe, Insulation for high temp steam service. 47. Steam Reducing station for #3 and #4 evap feed heater: misc damaged lagging in reducing station, steam strainer, valves, 6 and 8" steam piping, Insulation for high temp steam service. 48. Potable water fill line in overhead of S/A 6. 2 or 2 ½" pipe. Neoprene type insulation for low temp potable water service. 49. #4 Distillate cooler: heat exchanger needs relagging, neoprene type insulation for low temp sea water and potable water service. 50. #1 evap : Feed heat tube nest flange needs to be re insulated, check valve for air ejector need to be insulated 2" pipe, air ejector needs to be re-wrapped. High temp steam insulation service. 51. #2 Evap: Feed heat tube nest flange needs to be re insulated with high temp steam service insulation, damaged 8" neoprene water pipe run from 2nd stage to 3rd stage. 3rd stage tube nest head needs insulation to be re-installed. 52. Steam to #1 and #2 Evap reducing station: drain line 1 ¼" steam piping needs to be re-wrapped. The following FAR and DFAR provisions and clauses apply to this solicitation and are incorporated by reference: 52.204-7 Central Contractor Registration; 52.212-1 Instructions to Offerors-Commercial Items; 52.212-3 Alt I Offeror Representations and Certifications - Commercial Items (Offerors are advised to include a completed copy of this provision with their quote or a statement stating that it is available via the ORCA website, http://orca.bpn.gov.) 52.212-4 Contract Terms and Conditions-Commercial Items; 52.212-5 Contract Terms and Conditions Required to Implement Statutes or Executive Orders - Commercial Items 52.204-10 Reporting Executive Compensation and First-Tier Subcontract Awards 52.219-28 Post-Award Small Business Program Representation. 52.222-3 Convict Labor, 52.222-19 Child Labor - Cooperation with Authorities and Remedies, 52.222-21 Prohibition of Segregated Facilities, 52.222-26 Equal Opportunity, 52.222-35 Equal Opportunity for Disabled Veterans (over 100K) 52.222-36 Affirmative Action for Workers with Disabilities, (Over 15K) 52.222-37 Employment Reports on Special Disabled Veterans (When 52.222-35 Applies) 52.223-18 Contractor Policy to Ban Text Messaging While Driving 52.225-13 Restrictions on Certain Foreign Purchases, and 52.232-33 Payment by Electronic Funds Transfer --Central Contractor Registration 52.222-41 Service Contract Act 52.215-5 Facsimile Proposals: (757) 443-5982 252.204-7004 Required Central Contractor Registration. Alternate A; 252.212-7001 Contract Terms and Conditions Required to Implement Statutes or Executive Orders Application to Defense Acquisition of Commercial Items 252.225-7000 Buy American Act--Balance of Payments Program Certificate, 252.232-7003 Electronic Submission of Payment Requests; and 252.247-7023 Transportation of Supplies by Sea Alternate III. 52.252-2 Clauses Incorporated by Reference This contract incorporates one or more clauses by reference with the same force and effect as if they were given in full text. Upon request, the Contracting Officer will make their full text available. Also, the full text of a clause my be accessed electronically at this/these address(es): http://www.arnet.gov/far Responsible sources shall provide the following: 1. Price quote which identifies the requested item(s), unit price, and extended price 2. Total price 3. Prompt Payment Terms 4. Remittance address, Tax Identification Number, DUNS number and Cage Code 5. Responses to this solicitation are due 14 December 2011at 0800 local time, Norfolk, VA. LATE QUOTES MAY NOT BE CONSIDERED FOR EVALUATION. Quotes may be emailed to Roy.Williams@navy.mil or faxed via 757-443-5982 Attn: Roy Williams. Please reference the solicitation number on your quote. BASIS FOR AWARD: Award will be made to the responsible, technically acceptable quoter, whose quote, conforming to the combined Synopsis/Solicitation, offers the lowest evaluated price.
 

Web Link

FBO.gov Permalink
(https://www.fbo.gov/spg/DON/MSC/N322051/N40442-11-T-7169/listing.html)
 

Record

SN02340684-W 20101210/101208234152-e79c662524c3cdcb6a9738144077f892 (fbodaily.com)
 

Source

FedBizOpps Link to This Notice
(may not be valid after Archive Date)

---

| FSG Index  |  This Issue's Index  |  Today's FBO Daily Index Page |