SPECIAL NOTICE
51 -- SCREWDRIVER, ELECTRIC
- Notice Date
- 12/30/2008
- Notice Type
- Special Notice
- NAICS
- 332212
— Hand and Edge Tool Manufacturing
- Contracting Office
- General Services Administration, Federal Supply Service (FSS), GSA, FSS, Heartland Region (6FC and 6FL), 1500 East Bannister Road, Kansas City, Missouri, 64131
- ZIP Code
- 64131
- Solicitation Number
- QSDAAA-K8-01-508-1222
- Response Due
- 1/6/2009
- Archive Date
- 1/21/2009
- Point of Contact
- Ann C. Cooper, Phone: (816) 823-1390, Jacqueline A Simington,, Phone: (816)823-5123
- E-Mail Address
-
ann.cooper@gsa.gov, jackie.simington@gsa.gov
- Small Business Set-Aside
- Total Small Business
- Description
- NSN 5130-01-508-1222, SCREWDRIVER, ELECTRIC, quantity 10 each, one purchase order MPN-B-3K985-9M only. FOB point is Destination. Item must be manufactured in United State of America IAW 52.225-1. Any questions, please contact Ann Cooper at ann.cooper@gsa.gov. The description is below: This technical description covers Direct Current (DC) brushless motor (for spark limiting), variable speed, reversible, hex drive, battery powered screwdrivers with torque adjustment used for general maintenance and construction. This screwdriver shall be rated for use in Class I Division 2 Locations for maximum 50 degrees C ambient. Material: All materials used in the fabrication of the battery operated screwdrivers shall be new and of the quality necessary to produce battery powered screwdrivers to meet the requirements specified herein. Design: All parts of the battery powered screwdriver shall be designed and constructed to the requirements listed herein. All parts subject to wear shall be easily accessible for adjustment, replacement, or repair. Safety: The battery powered screwdriver shall provide safe and convenient operation when used in accordance with its intended design. However, the tool may involve use with hazardous materials, operations, and equipment. It is the responsibility of the user of this tool to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to its use. Users are cautioned to read all manufacturer's instructions prior to using the tool. In addition, the power screwdriver shall comply with the following safety requirements: Electrical components and motor shall be completely enclosed except for ventilation openings conforming to UL45, UL745, and UL60745. The tool shall be marked with a signal word "DANGER" followed by "This tool should only be used as a screwdriver. The use of this tool in any other way may result in the ignition of a flammable atmosphere." Interchangeability: All parts having the same manufacturer's number shall be manufactured to such standards that will permit replacement or adjustment without modification of the battery powered screwdriver or its parts. Construction: The battery powered screwdriver shall be completed so that when connected to the battery power source it can be used for its designed operation. Construction shall be free of any characteristics or defects that will prevent the screwdriver from passing any of the test specified herein this technical description. The battery powered screwdriver shall conform to the following design and performance requirements: Voltage: 12 Volts DC. Motor: 12 VDC Brushless. Drive Size: 1/4" Hexagon. Drive Type: Quick Release. Maximum No Load Speed: 400 RPM. Fastening Torque Range: 30 to 80 inch-lbs. Drive Style: Straight Handle Design: Pistol Grip Length (with battery pack): 7-15/32". Height (with battery pack): 10-15/32". Width (with battery pack): 2-13/16". Weight (with battery pack): 3.3 lbs. Features: When the fastening torque is preset, the driver shall shut off when the setting is reached. Battery shut off shall occur when capacity is less than 20 percent of full. Power Actuation Switch - The switch shall allow for operation in both forward and reverse directions. A safety setting to lock the switch in the off position to prevent accidental starts shall be provided. The switch shall be provided with an interlocking means that will prevent the switch from actuating the motor while the battery is being installed or removed from the tool. Clutch: The tool shall be provided with a clutch that can be adjusted throughout the full torque range in increments no greater than 1 inch-lb. The torque output at any given setting shall have a repeatability tolerance of +/-10% at +/-3 sigma. The clutch shall be provided with a device that automatically turns the tool off once the desired torque is reached while tightening the fastener. In addition the tool shall remain in the off position once the desired torque is reached for a minimum 0.5 seconds even if the power actuation switch is operated. Lubrication: The screwdrivers shall be pre-lubricated by the manufacturer so that the bearings and gears will be constantly lubricated when in operation. Bearings and gears that require subsequent lubrication shall be arranged so that the proper lubricant can be applied. Pressure lubricant fittings shall not be used. The gear housing shall be enclosed to prevent any leakage of the lubricant. Accessories: The screwdriver shall include the following accessories: Batteries: The screwdriver shall include two batteries each rated 2.0 ampere-hours. The battery pack shall be removable from the power driver for recharging. Each battery shall be capable of being fully discharged and recharged a minimum of 400 times. In addition a locking mechanism to prevent accidental disengagement of the battery pack shall be provided. Each battery shall also be provided with an interlocking means that will prevent the power actuation switch from operating the motor while the battery is being installed or removed from the tool. Charging Unit - The screwdriver shall be provided with one charging unit that shall comply with UL1012 or UL1310 as applicable. The charging unit shall include a light indicating a fully charged condition. The charger shall be capable of fully charging the battery pack in accordance with the manufacturer's instructions. Operating instructions and carrying case: The screwdriver shall be provided with one copy of the manufacturer's standard operating and maintenance instructions along with a sturdy metal or plastic carrying case, compartmentalized to prevent damage to the screwdriver and its components. Weight measurements shall include the screwdriver and battery pack. Test Requirements: Qualification: To qualify the design and processes a sample screwdriver shall be subjected to all requirements contained herein this technical description, including all tests contained in the referenced UL standards. The manufacturer shall maintain a record of compliance, with actual test data, for all units qualified. The manufacturer shall also perform testing to verify compliance with ratings and capacities listed herein this technical description and in catalog data sheets. A re-qualification shall be required whenever a change in design or manufacture affects qualification results. Acceptance: The battery powered screwdrivers shall be operationally checked for all functional characteristics including operation of the forward/reverse switch, trigger and locking mechanism, clutch mechanism, battery engagement and retention, battery and power actuation interlock system, and charger operation and weight. The charging units shall be tested in accordance with UL1012 or UL1310. Process Requirements: The manufacturing processes shall be monitored periodically to assure compliance with the following: Torque: The torque output at any given setting shall have a repeatability tolerance of +/-10% at 3 sigma. The screwdriver shall also provide a fastening torque range from 30 to 80 inch-pounds. The clutch used for various torque settings, shall be provided with a device that automatically turns the tool off once the desired torque is reached while tightening the fastener. In addition the tool shall remain in the off position once the desired torque is reached for a minimum 0.5 seconds even if the power actuation switch is operated. ITEM MARKING Mark each item in a permanent and legible manner with manufacturer's part number and name or identifying symbol. PACKAGING Shall be in accordance with the latest Edition of ASTM D 3951-98, "Practice for Commercial Packaging" available at www.ASTM.org. PACKING The unit packages shall be packed in a close fitting fiberboard box in compliance with the Uniform Freight Classification and the National Motor Freight Classification requirements of Rules, Item 222, Sec. 3., Minimum 200 psi, or Edge Crush Test (ECT) 32 Lbs. per Inch Width. MARKING All unit, intermediate, transport packages and unit loads shall be marked and bar coded for delivery to civilian activities in accordance with the latest version of FED-STD-123, "Marking For Shipment (Civil Agencies)", or marked and bar coded for delivery to military activities in accordance with the latest version of MIL-STD-129, "Military Marking For Shipment and Storage". "Latest version" is defined as the version in effect on the date of bid submittal. Federal Standards and Military Standards can be accessed on-line via the Defense Logistics Agency's "Assist" Quicksearch web site: http://assist.daps.dla.mil/quicksearch/. PALLETIZATION Pallet Configuration: The pallets shall be 48-inch length x 40-inch width, general purpose, four-way entry, flush stringer, double-face non-reversible pallets. Pallet lumber used shall be bark free. Pallet Load Size: The load plus the pallet shall have a maximum height of 53 inches and shall not exceed 2500 pounds in weight for shipments to Eastern Distribution Center (Burlington). The palletized load shall not exceed 2000 pounds in weight for shipments to the Western Distribution Center (Sharpe). Pallet Load Configuration: The containers or items shall be placed in a suitable pattern to form a stable and balanced load. Palletized loads shall be secured to the pallet to insure that the load arrives intact. Stacking Strength: The pallet plus the load shall be capable of supporting three additional like loads without any product damage and without the load or the pallet collapsing. Vertical, horizontal, or filler reinforcement may be added as necessary to provide strength. Partial Palletized Loads: Less than one-half pallet loads shall not be used for stacking, unless load is balanced on pallet. The partial palletized load shall be used for top loading only. NOTICE OF REQUIREMENTS FOR SHIPMENT TO EUROPEAN UNION COUNTRIES: Per Clause D-FSS-468, non-manufactured wood pallets and other non-manufactured wood package material used in shipments destined for ultimate delivery to or through a European Union (EU) country shall comply with the Emergency Measures (2001/219/EC) adopted by the Commission of the European Communities (CEC). Additionally, shipments delivered to DoD distribution facilities or freight consolidation points for eventual delivery to or through EU countries shall comply with DLA PROCLTR 01-15.
- Web Link
-
FedBizOpps Complete View
(https://www.fbo.gov/?s=opportunity&mode=form&id=eb366a135623f9baa8dea59ec42e62cf&tab=core&_cview=1)
- Record
- SN01725320-W 20090101/081230214736-eb366a135623f9baa8dea59ec42e62cf (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |