SOURCES SOUGHT
66 -- Purchase of Supplies - Yuma, AZ - GLI Brand Turbidity Analyzers
- Notice Date
- 11/14/2008
- Notice Type
- Sources Sought
- Contracting Office
- Department of the Interior, Bureau of Reclamation, Bureau of Reclamation, BOR/YAO Jessie Jones 928-343-8128 7301 CALLE AGUA SALADA YUMA AZ 85364
- ZIP Code
- 85364
- Solicitation Number
- 09SQ340041
- Response Due
- 11/21/2008
- Archive Date
- 11/14/2009
- Point of Contact
- Jessie K. Jones Purchasing Agent 9283438128 jjones@lc.usbr.gov;<br />
- Small Business Set-Aside
- Total Small Business
- Description
- This is a Sources Sought Notice ONLY. This is not a request for proposal, but a survey to locate potential sources. The US Bureau of Reclamation, Yuma Area Office, is performing a market survey to determine if there are an adequate number of interested firms having the capability to provide Great Lakes International brand turbidity analyzers as described below: Turbidity Analyzer Transmitter model: GLI Part #T53A4A1N, Sensor Model: GLI Part #8320T1A0C3NN Flow Rate................................... 0.05 to 7 GPM (0.19 to 26.5 LPM)Sample Temperature Range....... 32-140 F (0-60 C)Pressure Range: 0-50 psig at 68 F (0-3.4 bar at 20 C)Air Venting................................. Integral bubble trap for 0.05 to 0.5 GPM Light Sources............................. Two near-infrared (860 nM wavelength) LEDsSensor Flow Configuration......... Flow-through designWetted Materials........................ Non corrosive, PVC, polycarbonate, polystyrene, PPO, nitrile, and Buna-NCleaning Method........................Water rinse, wipe surfaces Enclosure: NEMA 4X (CSA type 4; IP65), molded fiberglass- reinforced polyester Mounting Configurations............. Both surface or pipe mountDisplay....................................... Graphic dot matrix LCD, 128 x 64 pixels with LED backlighting; 1/2 inch (13 mm) main character height; 1/8 inch (3mm) auxiliary information character height; menu screens contain up to six text lines Measurement Auto-ranging ScaleTurbidity................................ 0.000-100.0 NTU with auto-ranging and decimal point shift above 1.000 NTU and 10.00 TUAnalog Outputs (1 and 2)...... 4.00-20.00 mA Ambient Conditions:Operation.............................. -4 to +140 F (-20 to +60 C); 0-95% relative humidity, non-condensing Relays: Types/Outputs...................Four electromechanical relays; SPDT (Form C)contacts; U.L. rated 5A 115/230 VAC, 5A @ 30 VDC resistiveRelay Operational Mode..............Each relay (A, B, C, and D) can be assigned to be driven by the measured turbidity or diagnostics Function Modes:Control...................... Settings for high/low phasing, setpoint, deadband, overfeed timer, off delay, and on delayAlarm...........................Settings for low alarm point, low alarm point deadband, high alarm point, high alarm pointdeadband, off delay, and on delayStatus....................... Setting for FAIL, WARN or ALL system diagnostic conditions to activate relay when specific conditions exist (analyzer, light source 1/2 or detector 1/2 failure, sensor chamber dirty or sensor chamber unknown)Indicators...........................Relay annunciators (A, B, C, and D) indicate respective relay on/off status Sensor-to-Analyzer Sensor Distance...... 30 ft. (9 m) maximumPower Requirements.................. 120 VAC, 50/60 Hz. (10 VA max.) Calibration Methods:CUBE CAL............................. Temporarily insert an optional Cal-CubeTM assembly into the sensor and enter its factory certified standard value.HART.............. Enables configuration and retrieval of measured data for multiple analyzers over a communicationlink using appropriate hand-held terminal or data system with HART softwareMemory Backup (non-volatile).... All user settings are retained indefinitely in memory (EEPROM)EMI/RFI Conformance................Meets European standards for conducted and radiated emissions and immunity; certified CE compliant for applications as specified by EN 50081-1 for emissions and EN 50082-2 for immunity Electrical Certifications:General Purpose..... CSA, CSANRTL, and FM (UL pending)Class I, Div. 2 (Groups A-D).... CSA, CSANRTL, and FM (UL pending)Enclosure................................... NEMA 4X; polycarbonate face panel, epoxy coated cast aluminum door and case with four 1/2 inch (13 mm) conduit holes, nylon mounting bracket, and stainless hardwareMounting Configurations............. Panel, surface, and pipe mountingSystem Accuracy....................... 2% of reading, all rangesSensitivity.................................. 0.001 NTURepeatability.............................. 0.1% of span or betterTemperature Drift....................... Zero and Span: 0.01% of span per C Businesses who believe they are capable of providing these items shall submit their contact information as well as a statement of their business size under NAICS code 334513 (size standard 500 employees). This Sources Sought Notice is issued for the purpose of market research in accordance with Federal Acquisition Regulation (FAR) Part 10. All businesses capable of providing these supplies are invited to respond. Any information provided by industry to the Government as a result of this notice is voluntary. The Government will not pay for any information submitted in response to this notice. Send responses to Jessie Jones, Contract Specialist, at jjones@lc.usbr.gov, or fax number 928-343-8568.
- Web Link
-
FedBizOpps Complete View
(https://www.fbo.gov/?s=opportunity&mode=form&id=8b253594c4c9767620375f6f1a900018&tab=core&_cview=1)
- Place of Performance
- Address: Delivery Point: Yuma, Arizona<br />
- Zip Code: 85364<br />
- Zip Code: 85364<br />
- Record
- SN01705255-W 20081116/081114220452-8b253594c4c9767620375f6f1a900018 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |