SOLICITATION NOTICE
29 -- CONTROL UNIT,SUPERV
- Notice Date
- 12/11/2007
- Notice Type
- Solicitation Notice
- NAICS
- 336413
— Other Aircraft Parts and Auxiliary Equipment Manufacturing
- Contracting Office
- DEPARTMENT OF THE AIR FORCE; 3001 STAFF DR STE 2AG1 109B; TINKER AFB; OK; 73145
- ZIP Code
- 73145
- Solicitation Number
- FA8104-08-R-0149
- Response Due
- 1/25/2008
- Archive Date
- 4/24/2008
- Point of Contact
- Donna J Williams, Phone 405-734-8755, Fax 405-734-8781, Email donna.williams@tinker.af.mil
- E-Mail Address
-
Email your questions to Donna Williams
(donna.williams@tinker.af.mil)
- Small Business Set-Aside
- N/A
- Description
- CONTROL UNIT, NSN: 2995-01-520-3563NZ. P/N: 4088029D01. APPL: F100/-229 ENGINE. DESCRIPTION: Aluminum. The DEEC consists of a control cover and a control housing, that contain pressure transducers, input/output (I/O) connectors, and printed circuit board assemblies. Circuit board assemblies are interconnected by flexible cables and connectors. A center connector provides a signal cross link between circuit board assemblies housed within the control cover and control housing. I/O connectors provide electrical connection between and DEEC and engine sensors, interfaces and actuators. Unit cooling is provided by engine fuel via cooling passages in the control cover and control housing, with additional outer wall heat dissipation provided by nacelle air. Control Cover: Control cover is an aluminum casting, which includes a fuel outlet port connected to internal 1/4-inch diameter cooling cores, brackets for vibration isolators, a handle to simplify transport and cutouts for five I/O connectors. Control cover houses the Aircraft Interface Module and Engine Interface Module. Control Housing: Control housing is an aluminum casting, which includes a fuel inlet port connected to internal 1/4 inch diameter cooling cores, brackets for vibration isolators, cutouts for three pressure transducers and an I/O connectors. Control housing contains two printed circuit board assemblies: Converter Module, and processor and memory board assemblies. DESTINATION: 1 ea - FB6355 180 FW LGS Swanton, OH and 1 ea FB6563 138 FW LGTT Tulsa, OK. DELIVERY: 31 Dec 2008. QUANTITY: 2 ea. SOLICITATION: FA8104-08-R-0149. QUALIFICATION REQUIREMENTS: This part will be acquired directly from the actual mfg. Drawings are proprietary to Hamilton Sundstrand Corp. The government does not own sufficient data to compete this item. Due to the complexity and criticality of this part, only actual manufacturers that have successfully completed all testing required by the original company responsible for the design, can be considered approved sources for this item. Written quotations for sub-contracting opportunities should be submitted TO: HAMILTON SUNDSTRAND CORPORATION, WINDSOR LOCKS, CT 06096-1000 (cage code 73030). The requirements of FAR 9.202(a)(1) have been completed and copies of the qualification requirements and standards may be obtained as described in the solicitation. These qualification requirements apply to line item(s) 0001. The approximate response date will be 26 JAN 2008. The anticipated award date is 26 FEB 2008. Electronic procedures will be used for this solicitation. All responsible sources solicited may submit a bid, proposal, or quotation that shall be considered. JUSTIFICATION: Supplies (or Services) required are available from only one or a limited number of responsible source(s) and no other type of supplies or services will satisfy agency requirements. Award will be made only if the offeror, the product/service, or the manufacturer meets qualification requirements at the time of award in accordance with FAR clause 52.209-1. The solicitation identifies the office where additional information can be obtained concerning qualification requirements as cited in each individual solicitation. It is suggested that small business firms or others interested in subcontracting opportunities in connection with the described procurement make contact with the firm(s) listed above. Note: While price will be a significant factor in the evaluation of offers, the final contract award decision may be based upon a combination of price and past performance factors as detailed in the solicitation. Note: An Ombudsman has been appointed to hear concerns from offerors or potential offerors during the proposal development phase of this acquisition. The purpose of the Ombudsman is not to diminish the authority of the program director or contracting officer, but to communicate contractor concerns, issues, disagreements, and recommendations to the appropriate government personnel. When requested, the Ombudsman will maintain strict confidentiality as to the source of the concern. The Ombudsman does not participate in the evaluation of proposals or in the source selection process. Interested parties are invited to call the Ombudsman at (405)736-3273. DO NOT CALL THIS NUMBER FOR SOLICITATION REQUESTS. Note: The solicitation will be posted on the FedBiz Ops on or about 26 DEC 2007. See note(s) 22, 23 & 26.
- Record
- SN01467698-W 20071213/071211223653 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |