SOLICITATION NOTICE
59 -- MEDIUM VOLTAGE ELECTRICAL CABLE, Three (3) rolls, 3500 feet on each reel, Medium Voltage (15 kV) Underwater Cable.
- Notice Date
- 5/5/2006
- Notice Type
- Solicitation Notice
- Contracting Office
- DOT/Maritime Administration, WR Acquisition 201 Mission Street, Suite 1800 San Francisco CA 94105
- ZIP Code
- 94105
- Solicitation Number
- DTMA4Q06025
- Response Due
- 5/22/2006
- Archive Date
- 5/5/2007
- Small Business Set-Aside
- Total Small Business
- Description
- For this solicitation, United States DOT Maritime Administration intends to conduct an online competitive reverse auction to be facilitated by the third-party reverse auction provider, FedBid, Inc. FedBid has developed an online, anonymous, browser based application to conduct the reverse auction. An Offeror may submit a series of pricing quotes, which descend in price during the specified period of time for the aforementioned reverse auction. United States DOT Maritime Administration is taking this action in an effort to improve vendor access and awareness of requests while expediting its ability to gather multiple, completed, real-time offers. All responsible Offerors that respond to this solicitation MUST submit the pricing portion of their offer using the online exchange located at www.FedBid.com. There is no cost to register, review procurement data or make an offer on www.FedBid.com. Offerors that are not currently registered to use www.FedBid.com should proceed to www.FedBid.com to complete their free registration. Offerors that require special considerations or assistance may contact the FedBid Helpdesk at 877-9FEDBID (877-933-3243) or via email at clientservices@fedbid.com. Offerors may not artificially manipulate the price of a transaction on www.FedBid.com by any means. It is unacceptable to place bad faith offers, to use decoys in the www.FedBid.com process or to collude with the intent or effect of hampering the competitive www.FedBid.com process. Should offerors require additional clarification, contact James Bartha at jim.bartha@dot.gov or FedBid.com at 877-9FEDBID (877-933-3243) or clientservices@fedbid.com. Solicitation number is DTMA4Q06025. The estimated posting on FedBid is 4/16/2006, with an estiamted closing on FedBid of 5/22/2006. Estimated award date is 5/24/2006. NAICS CODE 421610 SIC 5063 Detalis of the requirment follow: Medium Voltage (15 kV) Underwater Cable 3/25/05 The publications listed below form a part of this specification to the extent referenced. The publications referred herein are by the basic designation only. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) ANSI/ASTM B8 1986 Standard Specification for Concentric-Lay- Standard Copper Conductors, Hard, Medium Hard, or Soft ANSI/ASTM B33 1985 Standard Specification for Tinned Soft or Annealed Copper Wire for Electrical Purposes ANSI/ASTM B 189 1990 Standard Specification for Lead-Coated and Lead-Alloy-Coated Soft Copper Wire for Electrical Purposes ASSOCIATION OF EDISON ILLUMINATING COMPANIES (AEIC) AEIC CS6 1987 Specifications for Ethylene, Propylene, Rubber Insulated Shielded Power Cables Rated 5-69 kV INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS, INC. (IEEE) IEEE 48 1990 High-Voltage Alternating-Current Cable Terminations IEEE 404 1986 Cable Joints for Use with Extruded Dielectric Cable Rated 5000V Through 46000V and Cable Joints for Use With Laminated Dielectric Cable Rated 2500V Through 500,000V UNDERWRITERS LABORATORIES INC. (UL) UL 83 1983 (R 1989) (Bul. 1990) Thermoplastic-Insulated Wires And Cables, Ninth Edition UL 486A 1980 (R 1989) Wire Connectors and Soldering Lugs For Use with Copper Conductors, Seventh Edition UL 510 1986 (R 1986) Insulating Tape, Sixth Edition INSULATED CABLE ENGINEERS ASSOCIATION ICEA S-66-524 1988, Cross-Linked Thermosetting-Polyethylene-Insulated Wire and Cable for the Transmission And Distribution of Electrical Energy ICEA S-68-516 1988, Ethylene-Propylene-Rubber-Insulated Wire and Cable For the Transmission And Distribution of Electrical Energy Cable Requirements The Vendor shall submit to the Government the following: 1.3.1 Manufacturer's catalog data for the Medium Voltage MPF-GC Underwater Cable. 1.3.2 Drawings for the Medium Voltage MPF-GC Underwater Cable 1.3.3 Submit the manufacturers' test reports for cables as follows: a. Conductor DC resistance shall meet ICEA S-68-516 requirements b. Each reel of cable shall be subject to the AC and DC tests as follows: A five (5) minute AC withstand test with 44 kV shall be accomplished. A 15 minute DC withstand test accomplished using NETA Specifications. c. Insulation resistance shall be measured and reported in megaohms per 1000 ft. The Specific Insulation Resistance (SIR), corrected to 60 degrees Fahrenheit, shall not be less than 50,000. d. The completed conductors shall be tested for corona discharge and shall comply with AEIC requirements. On long lengths of cable, corona will be limited to maximum manufactured conductor lengths. e. Testing will be done in preliminary and final stage. 1. Preliminary tests shall be conducted on insulated and shielded single conductors prior to any further processing. These tests shall be high voltage AC, IR and DC tested as well as corona test at the high voltage test values of paragraph b. above. 2. Final test shall be on full lengths of completed cable. The full length of each cable shall withstand a ten minute high voltage DC test at 80% of the high voltage DC test value (paragraph b. above) applied between the conductor and grounded external shield. Prior to this the metallic shield shall be checked end-to-end for continuity. f. Samples from the completed cables shall be tested in accordance with the pertinent ICEA specifications. Indicate the specific tests performed and include results of tests per 1.5.3. As a minimum, the following tests are to be performed. Jacket Tests - Aging - Vertical Flame Test - Jacket Tensil Strength - Mechanical Water Absorption - Cold Bend - Smoke Generation - Specific Resistivity Insulation Tests - Tensile Strength - Ozone Resistance - SIC @ 80V/mil - % Power Factor @ 80V/mil Tests After 24 Hours Water Immersion - SIC @ 80V/mil - % Power Factor @ 80 V/Mil - Maximum Water Absorption After 7 Days Immersion 1.4 Vendor is to provide for the following field test reports upon delivery of the cable at destination: a. Insulation resistance test b. Continuity test c. High potential (hi-pot) test d. Medium voltage cable tests e. Grounding systems test When testing systems, identify each system for each test. 1.5 Certificates Vendor shall provide certification of cable testing. PART 2 PRODUCTS SUMMARY of Medium Voltage (15 kV) MPF-GC Underwater Cable: 3/C #2 AWG - 15 kV - Type MPFG. Note: Outside diameter of cable must be 2 3/8 inches. The cable shall consist of three (3) Class B stranded coated copper conductors with extruded semiconducting strand screen, 133% (220 mils) red colored EPR insulation, extruded semiconducting insulation screen over each conductor, and metallic shielding of soft annealed coated copper tape with 25% overlap per ICEA S-68-516 part 4.1.1.2, cabled with two bare copper, Class B stranded ground wire/s, one (1) yellow insulated (600V) ground check wire #8 AWG, polyethylene fillers, and outer overall extra heavy duty jacket of Hypalon chlorinated polyethylene (CPE). The MPF-GC cable shall be assembled into a length as specified on the project plans. Each cable length shall be terminated with a cable coupler, male on one end and female on the other end. 2.1 MATERIALS AND EQUIPMENT 2.1.1 Power Wire and Cable 2.1.1.1 Wire and Cable Conductor Sizes Conductor and conduit sizes indicated are for copper conductors unless otherwise noted. WIRES AND CABLES MANUFACTURED MORE THAN 12 MONTHS PRIOR TO DATE DELIVERED TO THE SBRF SHALL NOT BE USED. Conductors: All conductors shall be copper. 2.1.2 Medium Voltage Cable 2.1.3.1 Medium Voltage (15 kV) MPFG Underwater Cable Underwater cable shall be rated for 15 kV at an insulation level of 133% (220 mils). The cable assembly shall consist of three (3) stranded copper conductors, each covered by an extruded semiconducting strand shield, ethylene-propylene rubber conductor insulation, extruded semiconducting insulation screen, and a copper shield. The three conductors shall be assembled into a single cable assembly utilizing polyethylene fillers, and extra heavy duty chlorinated polyethylene (CPE) (Hypalon) overall extruded jacket. Provide two (2) bare copper ground wires (#6 AWG minimum) and one (1) 600V yellow insulated ground check wire #8 AWG. The assembly shall further be assembled as follows: a. The power conductors shall be uncoated soft copper wire, Class B, stranded, compressed concentric round copper per ASTM B-8 and shall meet the electrical resistance requirements of ICEA S-68-516, Section 2.5. b. An extruded layer of semiconducting EPR compound with a volume resistivity not in excess of 1000 ohm meters shall be applied over the conductor. The compound shall have a minimum elongation after an air oven test at 121 degrees Celsius for 168 hours at 100% and a brittleness temperature not warmer than -50 degrees Celsius. The screen shall be clean striping from the conductor and inseparably bonded to the overlying insulation. The thickness of the extruded conductor screen shall be a minimum of 12 mils point and a minimumof 15 mils average. c. Insulation shall be EPR, a red colored ethylene propylene rubber. The insulation shall be formulated by the cable manufacturer in his own facility using a closed system to ensure maximum cleanliness. The EPR insulation shall be extruded with conductor shield to prevent intersurface contamination. Accurate individual control and measurement of the wall thickness of each layer of compound shall be maintained while the cable is being manufactured. d. The wall thickness of the insulation shall be 220 mils. The minimum average wall thickness at any cross section shall not be less than 90% of the specified minimum average. e. An extruded round layer of semiconducting EPR compound with a volume resistivity not in excess of 500 ohm meter at 90 degrees Celsius when tested per AEIC No. CS6 shall be applied over the insulation. The extruded screen shall be applied over the insulation. The thickness of the extruded screen shall be 40 mils point minimum per AEIC CS6. The phase conductors shall be color coded or identified with color legend tape. The outer surface of the screen shall be printed with white ink - "Semiconducting Remove When Splicing or Terminating". f. Each conductor shall have one (1) metallic shield of 5 mil bare copper tape lap applied directly over the insulation screen. g. Two (2) #6 AWG bare copper ground wires. h. One (1) #8 AWG - 600V - yellow insulated ground check wire. i. The cable shall be assembled in accord with ICEA S-68-516, Part 5. Polyethylene fiber fillers shall be inserted as required to produce a substantially round core. A marker tape showing manufacturer, plant no., year of manufacture shall be inserted. A binder tape with 50% lap shall be wrapped over the assembly. j Extruded over the assembly core shall be an extra heavy duty (Hypalon) chlorinated polyethylene (CPE) jacket. 2.2 SIZE 3500 feet 15kv cable with ADALET/PLM 500 AMP -3 Phase Couplers. o One (1) SFL415AR-P Female socket o One (1) PML415ALK male plug Install one (1) each on the end of each cable. ADALET plugs are required to match existing system. 2.3 VENDORS DRAWINGS REQUIRED Vendors drawings shall include, but not be limited to the following: a. Overall dimensions and sectional views of ADALET plugs
- Web Link
-
Please click here to view more details.
(http://ideasec.nbc.gov/j2ee/announcementdetail.jsp?serverId=MR693800&objId=265381)
- Place of Performance
- Address: Delivery to Benicia, CA
- Zip Code: 94510
- Country: USA
- Zip Code: 94510
- Record
- SN01042718-W 20060507/060505221655 (fbodaily.com)
- Source
-
FedBizOpps Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |