MODIFICATION
66 -- Laser Tracker Measuring System with Absolute Distance Meter only (ADM)
- Notice Date
- 8/12/2005
- Notice Type
- Modification
- NAICS
- 334519
— Other Measuring and Controlling Device Manufacturing
- Contracting Office
- Department of Commerce, National Institute of Standards and Technology (NIST), Acquisition Management Division, 100 Bureau Drive, Building 301, Room B129, Mail Stop 1640, Gaithersburg, MD, 20899-1640
- ZIP Code
- 20899-1640
- Solicitation Number
- SB1341-05-Q-0904
- Response Due
- 8/25/2005
- Archive Date
- 9/9/2005
- Small Business Set-Aside
- Total Small Business
- Description
- The Purpose of this amendment is: 1. Post a revision to the specifications for the Laser Tracker Measuring System with Absolute Distance Meter only (ADM). 2. Extend the response date from August 18, 2005 to August 25, 2005. The specifications are revised to read: All interested offerors shall provide a quote for the following line items: Line Item 0001: One (1) Each, Laser Tracker Measuring System with Absolute Distance Meter only (ADM). Laser tracker Measuring System shall have the following specifications: All specifications shall be specified per Draft ASME B89.4.19. That is, the manufacturer must provide all of the specifications listed in forms 3.1 (General Specification and Rated Conditions) and 3.2 (Manufacturer?s Performance Specifications) of the draft B89.4.19 Standard. Additionally the supplier must provide a formula for calculating the MPE for any length measurement within the laser tracker work volume. The manufacturer?s specifications shall not exceed the values for each measurement position listed in the table on the following page. These specifications shall be valid over the operating range of 18.0 to 30.0 degrees Celsius. The tracker must have a measuring range of at least 30 meters and for the purposes of specifying the ADM range test the MPE shall be specified for a maximum range of 30 meters or R=30. Acceptance A tracker that meets the government requirement for this request must conform to the specifications listed in this document. For the purposes of this document, Conform to the Specifications requires that the B89.4.19 tests be performed at NIST by NIST large-scale coordinate metrology staff. NIST will not compensate the manufacturer for travel or other expenses associated with testing the tracker on-site at NIST. Range Software ADM range value ADM Tracker Specifications Test (positions) MPEADM micrometers Horizontal (1) 60 Horizontal (2,3,4,5) 80 Horizontal (6,7,8,9) 120 Vertical (1,2,3,4) 80 Vertical (5,6,7,8) 120 Right Diagonal (1,2,3,4) 80 Right Diagonal (5,6,7,8) 120 Left Diagonal (1,2,3,4) 80 Left Diagonal (5,6,7,8) 120 User Selected (1) Default 60 User Selected (2) Default 100 Two Face (1,2,3,4) 100 Two Face (5,6,7,8) 120 Two Face (9,10,11,12) 160 ADM Ranging Test (1) 30 ADM Ranging Test (2) 40 ADM Ranging Test (3) 45 ADM Ranging Test (4) 50 ADM Ranging Test User (1) 50% maximum range 45 ADM Ranging Test User (2) 60% maximum range 48 Formula for calculating the MPE (or attach MPE specification sheet All other terms and conditions remain the same.
- Place of Performance
- Address: 100 Bureau Drive, Shipping & Receiving, Building 301, Gaithersburg, Maryland
- Zip Code: 20899-0001
- Country: USA
- Zip Code: 20899-0001
- Record
- SN00869149-W 20050814/050812211840 (fbodaily.com)
- Source
-
FedBizOpps.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |