SOURCES SOUGHT
99 -- REQUEST FOR EXPRESSION OF INTEREST FROM PROSPECTIVE VENDORS TO PROVIDE A BROKK 330 N OR EQUAL
- Notice Date
- 1/31/2003
- Notice Type
- Sources Sought
- Contracting Office
- Department of Energy, Idaho Nat'l Engineering and Environmental Laboratory (DOE Contractor), Idaho National Engineering & Environmental Laboratory, 2525 Fremont P.O. Box 1625, Idaho Falls, ID, 83415-3805
- ZIP Code
- 83415-3805
- Solicitation Number
- Reference-Number-PROC9
- Archive Date
- 3/4/2003
- Point of Contact
- Sonja Rish, Consulting Office Specialist, Phone 208-526-2290, Fax 208-526-7743, - Sonja Rish, Consulting Office Specialist, Phone 208-526-2290, Fax 208-526-7743,
- E-Mail Address
-
sja@inel.gov, sja@inel.gov
- Description
- I. Introduction: Bechtel BWXT Idaho, LLC (BBWI), Management & Operating Contractor of the Idaho National Engineering and Environmental Laboratory (INEEL), is requesting an Expression Of Interest (EOI) from prospective vendors to provide a BROKK 330N or equal. The BROKK 330N (nuclear grade) remote controlled electro-hydraulic driven Demolition Vehicle with end-effector tool attachments is required for demolition of nuclear process equipment and facilities. The required equipment must include: 1) remote tele-operated control, 2) wireless RF control system, 3) a remote tool interface system, 4) electrically powered with a cable management system and 5) hydraulically operated demolition unit. The demolition equipment must have a minimum 15ft vertical reach and 1700 lb. lift capacity at full extension at the remote tool interface. The unit must fit through a 6ft wide by 6ft high opening, create less than 75 psi ground loading and weigh less than 12,000 lb. including the maximum load. The required end effectors include: 1) BROKK HC600 or equal steel shear, 2) clamshell bucket with a 4 cubic feet capacity, 3) backhoe bucket 20 inch wide 6 cubic feet capacity, and 4) cold cut saw. To be considered for solicitation, potential suppliers must provide evidence that the equipment to be offered has a history of successful applications in demolition of nuclear process equipment and facilities. The required equipment must be commercially available (not custom designed). This request for EOI shall serve as a method of screening potential vendors; allowing only vendors proposing to offer equipment determined by BBWI to meet the identified requirements to receive a formal Request for Proposal (RFP). II. Submittal: It is the intent of this request for EOI to identify candidate vendors who have readily available equipment offered as a standard product by catalog/part number. Custom designed equipment will NOT be considered. Your submittal shall include vendor catalog/part numbers and catalog cuts for the equipment to be proposed. Potential vendors are requested to provide a written EOI including the submittal information delineated herein to A. E. French, BBWI GEM Project Procurement Manager, P.O. Box 1625, 2525 Fremont Ave., Idaho Falls, ID 83415-3975 by close of business, 2/17/03. If additional information is required, please contact Mr. French at (208) 526-3771 or email at aef@inel.gov. Technical questions must be submitted in writing (U.S. Mail or e-mail). Point of Contact Alan E. French Project Procurement Manager, Phone 208-526-3771, or E-mail aef@inel.gov Place of Contract Performance The required equipment will be delivered to BBWI at the INEEL.
- Place of Performance
- Address: At the vendor's facility. The equipment will be delivered to the Idaho National and Engineering Laboratory (INEEL) 50 miles west of Idaho Falls, ID.
- Zip Code: 83415-3920
- Country: USA
- Zip Code: 83415-3920
- Record
- SN00250325-W 20030202/030131213313 (fbodaily.com)
- Source
-
FedBizOpps.gov Link to This Notice
(may not be valid after Archive Date)
| FSG Index | This Issue's Index | Today's FBO Daily Index Page |